{"product_id":"10321-lenz-21-pin-silver-loco-decoder","title":"10321 Lenz 21 Pin Silver Loco Decoder","description":"10321 Lenz 21-pin Silver Loco Decoder. Motor current 1amp continuous, 1.8 amp maximum, 21-pin Plug Connection, 4 Function outputs, Dimensions 23mm length x 16.6mm wide x 3.5mm height. Load capacity 4 x 100mA.  \u003cp\u003eThe new silver series decoders revolutionize decoder technology.\u003c\/p\u003e  \u003cp\u003eFEATURES\u003c\/p\u003e  \u003cp\u003eMotor control\u003c\/p\u003e  \u003cp\u003eThe decoder has a high-frequency control (23kHz) with Back EMF. To adapt it to the type of locomotive used, you can simply choose between different motor types. These individual motor types include parameter sets which have been specially adapted to the respective models. Moreover, it is also possible to carry out fine-tuning via various CVs. Of course you can switch off both the high-frequency control as well as the control system itself. The minimum, maximum and mid speed can be set; the decoder adapts the characteristic speed line dynamically to ensure a steady, smooth curve. Independently of this, it is also possible to program an individual characteristic speed line. You can use up to 128 running notches.\u003c\/p\u003e  \u003cp\u003eCapacity\u003c\/p\u003e  \u003cp\u003eWe have defined the continuous or maximum current-carrying capacities of the GOLD decoder motor outputs. The continuous load is achieved without special installation of heat sinks or other cooling methods\u003c\/p\u003e  \u003cp\u003eOverload protection\u003c\/p\u003e  \u003cp\u003eThe decoders are protected against overloading, short circuits and overheating.\u003c\/p\u003e  \u003cp\u003eStarting and braking delay\u003c\/p\u003e  \u003cp\u003eThe starting and braking delays can be set independently of each other. These delays can be enabled and disabled via a function by pressing the key (default setting function 4) of the digital system once.\u003c\/p\u003e  \u003cp\u003eConstant braking distance\u003c\/p\u003e  \u003cp\u003eA special feature of the GOLD decoder provides for a constant braking distance independent of the current speed of the locomotive. This feature is important for model railway operators who install automatic stopping sections in their layouts.\u003c\/p\u003e  \u003cp\u003eShunting speed\u003c\/p\u003e  \u003cp\u003eThe shunting speed can be set via a function; (default setting function 3) it halves the speed.\u003c\/p\u003e  \u003cp\u003eABC = simple signal stop and slow approach\u003c\/p\u003e  \u003cp\u003eYou can carry out a particularly simple signal stop using the ABC braking module e. g. the BM1 module. Combined with the constant braking distance, precise on-the-spot stopping in front of red signals is not a problem. The signal indication \"\"Slow approach\/Caution\"\" does not pose a problem; the respective speed can be set via a CV in the decoder. You can operate all functions during the signal stop or slow approach - you can even reverse away again from the red signal. The special ABC modules BM3 can be used to assemble a block section of any desired length.\u003c\/p\u003e  \u003cp\u003ePush-pull train control\u003c\/p\u003e  \u003cp\u003eA push-pull train control can be set if the ABC braking module BM2 is used. There are two different options: push-pull operation with and without intermediate stops. The latter also takes slow-approach sections into account. The stopping time at the end of the track and at the intermediate stops is set at between 1 and 255 seconds via a CV.\u003c\/p\u003e  \u003cp\u003eFunction outputs\u003c\/p\u003e  \u003cp\u003eFour function outputs can be mapped to the functions of the digital system according to NMRA.\u003c\/p\u003e  \u003cp\u003eLighting effects\u003c\/p\u003e  \u003cp\u003eDifferent lighting effects can be set at the four function outputs:\u003c\/p\u003e  \u003cp\u003eSetting the brightness (dimming), can be switched via a function as desired\u003c\/p\u003e  \u003cp\u003eMars light\u003c\/p\u003e  \u003cp\u003eGyra light\u003c\/p\u003e  \u003cp\u003eStrobe and double strobe\u003c\/p\u003e  \u003cp\u003eDifferent settings for random flickering (ideal for a steam locomotive fire box)\u003c\/p\u003e  \u003cp\u003eFlashing\u003c\/p\u003e","brand":"Lenz Digital","offers":[{"title":"Default Title","offer_id":56355433546108,"sku":"LZ10321","price":34.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0943\/3048\/7164\/files\/10321_82726465-e788-4e5c-8117-70d6548da5c3.jpg?v=1786091653","url":"https:\/\/www.kernowmodelrailcentre.com\/products\/10321-lenz-21-pin-silver-loco-decoder","provider":"Kernow Model Rail Centre","version":"1.0","type":"link"}